Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.

Don't undervalue the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which virtually created casualties.
Instance 3: The width of the forklift cargo exceeds the allowable size of the course and hangs on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding up and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn first and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a load, the chauffeur should initially confirm that the lots is steady and reliable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork needs to be reduced to the typical driving position before driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal must be issued initially. High-speed sharp turns are forbidden. High-speed sharp turns will certainly trigger the car to shed side security and topple. .
5. When the forklift is downhill, it is strictly prohibited to shut off the flame and slide, and it is prohibited to brake all of a sudden while driving with loads unless there are special scenarios.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and need to keep a specific security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and dumping.
1. When fork-loading things, the distance in between both forks ought to be adjusted as required to make the load of both forks balanced and not skewed, and one side of the thing ought to protest the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In special scenarios, safety indication should be set up to remind surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is reduced to permit simple placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and air conditioning water must be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the vehicle;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no Electric Forklift Truck for Warehouse activating the slope is allowed.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift Stand-on Electric Pallet Stacker employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844